| HDMI Video Resolution & Frequency Problem. | |
|---|
|
|---|
| | 
Alexander Gent
Posts 77
24 Mar 2022 22:00
|  I am trying to setup the screen mode on my Toshiba monitor to display resolution
1360x768 (as per above picture) but all I get is a blank screen.
Is there a walk through guide to explain how to setup screen modes?
I have tried to configure the screen modes using the Picasso96 and
PicassoTNG preferences editors but not having much luck.
Thank you.
| |
| | 
Edgar Fink
Posts 47
25 Mar 2022 08:14
| It is a trial and error thing, but I have had luck using "cvt" from aminet: EXTERNAL LINK or umc:
EXTERNAL LINK
With umc you can try along these lines to generate a mode line which you can put in to Picasso96 prefs:
umc 1360 768 85500000 -rbtAs far as I remember the rbt option is key here. This is from memory, so I am not sure the above is correct. Read the docs and rinse and repeat. There is a thread here you might find useful:
CLICK HERE
| |
| |
Alexander Gent
Posts 77
27 Mar 2022 04:53
| Edgar Fink wrote:
|
It is a trial and error thing, but I have had luck using "cvt" from aminet: EXTERNAL LINK or umc:
EXTERNAL LINK
With umc you can try along these lines to generate a mode line which you can put in to Picasso96 prefs:
umc 1360 768 85500000 -rbt
As far as I remember the rbt option is key here.
This is from memory, so I am not sure the above is correct. Read the docs and rinse and repeat.
There is a thread here you might find useful:
CLICK HERE |
Hi Edgar,
Those utilities were very helpful.
Using PicassoModeTNG I was able install new video screen modes.
Only 2 resolutions didn't work, but I managed to get a nice 1280x720 16bit colour resolution. Nice! Thank you...
| |
| |
Edgar Fink
Posts 47
28 Mar 2022 08:16
| That's cool and you're welcome. You should keep trying with te 1360x768 resolution, I have learned that adjusting the clock rate to below the required by steps of 10 or 5 sometimes work with some monitors. Did you try the rbt option with umc?
| |
| | 
Pat 3657
Posts 50
28 Mar 2022 10:13
| Just checking: Is the tool setting OVERCLOCK set to YES ?
If set to NO, Picasso96Mode caps the pixel clock at 50 MHz.
1360x768@60Hz should be possible with a pixel clock around 70 Mhz.1360x768
Clock: 70.23 MHz
Interlace: no
DoubleScan: no
Framesize: 1460x800
Bordersize: 0x0
Position: 16/2
Syncsize: 64/0
= Frequency 48kHz/60Hz If this does not work for you, try increasing the framesize and clock (as a bigger framesize decreases frequency below 60 Hz).
| |
| |
Alexander Gent
Posts 77
06 Apr 2022 09:50
| Pat 3657 wrote:
|
Just checking: Is the tool setting OVERCLOCK set to YES ?
If set to NO, Picasso96Mode caps the pixel clock at 50 MHz.
1360x768@60Hz should be possible with a pixel clock around 70 Mhz.
1360x768
Clock: 70.23 MHz
Interlace: no
DoubleScan: no
Framesize: 1460x800
Bordersize: 0x0
Position: 16/2
Syncsize: 64/0
= Frequency 48kHz/60Hz
If this does not work for you, try increasing the framesize and clock (as a bigger framesize decreases frequency below 60 Hz).
|
Hi Pat,
The tool setting is set to OVERCLOCK. No matter what I try I can't get the monitor to output to 1360x768 or 1280x768. However it does work with 1280x720.
In the grand scheme, I happy with the results. It is just one of those things... Thank you.
| |
|
Documentation about the Vampire hardware